InstalSystem 5
Revision as of 10:13, 21 April 2022 by Pszczolkam (talk | contribs)
Product information
- Educational version features
- List of standards and methods used for sizing and calculations
- Release notes InstalSystem 5
- Package technical specifications
Designing lessons
- Introduction to the work with the package InstalSystem 5
- Calculation of cooling capacity for radiant systems (floor, wall or ceiling)
- Calculation of design heat load of rooms
- Designing heating systems with convective radiators
- Designing installations with flat stations
- Designing of radiant heating floor and wall installation
- Designing of radiant heating installation on the basis of data from the Smart application
- Designing of water supply system installation
- Designing radiant (ceiling, wall) panel heating/cooling systems
- Designing radiant heating systems with pipe-runs as distribution system
- Designing sanitary system loop installations
- Designing sewage installations
- Quick design of radiant heating/radiant cooling
- Radiant steel ceiling panels
Sample projects
- Convective heating installation and water supply system with use of flat stations in a multifunctional building
- Convective heating installation with risers
- Installation with cooling radiant and panel systems in multifunctional building
- Installation with underfloor and wall radiant heating system in single family building
- Water supply system in multifunctional building
Functions and tools
- Appending drawings with radiant system loops
- Automatically connect terminal units
- Automatically generate schematic views
- Combine base files
- Connecting storeys with the "Stack" element
- Design based on a project file from InstalSystem 4
- Drawing chart
- Editing data of Building units
- Export / print results and drawings
- General data
- Ground modeling
- Heating/cooling zone
- Heating/cooling zone build-up editor
- Import of building model from BIM compatible formats
- Import underlay files
- Inserting plates in dry floor heating system
- Installation, activation and update InstalSystem 5 package
- Interactive calculations of radiant systems
- Manifold table
- Manifolds for radiant system and their accessories
- Pipe feeds route and editing pipe feeds in a radiant system
- Pipe feeds route - Good practices and use cases
- Preparation of building structure
- Preparation of building structure - Creation of a loggia
- Preparation of building structure - Creation of roofs with different construction
- Preparation of building structure - Multi-storey rooms
- Preparation of building structure - Rooms layout
- Preparation of building structure - Without rooms
- Presentation of the calculations result
- Project and application management
- Search components in the project
- Selecting and editing multiple elements
- Software configuration
- Terminal unit
- Using catalogs and catalogs data in the project
- Wall geometry correction
- View navigation in the graphical editor
Tips&Tricks
- Differences in the room volume calculation between version 4 and version 5
- General recommendations for users of InstalSystem 4 starting work with InstalSystem 5
- Heat source dimensioning for installations with flat stations
- How to calculate a file using a package configuration other than the one under which the file was created
- How to eliminate: "Automatic division of H/C Zone not possible"
- How to eliminate: "Automatic arrangement of pipe feeds not possible - change pipe feeds route or H/C Zone parameters or arrange pipe feeds manually"
- How to eliminate: "Cannot apply any pipe spacing"
- How to eliminate: "Incorrect building contour"
- How to eliminate: "MAXIMUM PERMISSIBLE PRESSURE DROP ON VALVE EXCEEDED"
- How to eliminate: "No R.H./R.C. loop found. Loop drawing required for heating/cooling output calculations"
- How to eliminate: "The pipe-run is part of the receiver connection"
- How to eliminate: "Unbalanced circuit of terminal unit "XY"..."
- How to get better quality of resultant PDF files
- How to get the required position of radiator circuit pipes in 3D view
- How to include the drawing loop lenght in the calculations?
- How to make the program run faster
- How to properly connect manifold with heating/cooling zone using pipe feeds route
- How to shorten calculation time
- Problems with the application on computers with integrated graphics card
- Radiant heating systems - how to improve thermal and hydraulic results
How to eliminate: "PRESSURE DROP TOO HIGH - modify the parameters of H/C Zone or H/C Area"