Determination of adjacent space temperature: Difference between revisions
Klintsevicho (talk | contribs) No edit summary |
Klintsevicho (talk | contribs) No edit summary |
||
| Line 45: | Line 45: | ||
'''<IS_TS id=strs_expidISFOZCDaneOgolneSredniaTemperaturaZewnetrzna/>''' - ''<IS_TS id=strl_expidISFOZCDaneOgolneSredniaTemperaturaZewnetrzna/>''.<br/> | '''<IS_TS id=strs_expidISFOZCDaneOgolneSredniaTemperaturaZewnetrzna/>''' - ''<IS_TS id=strl_expidISFOZCDaneOgolneSredniaTemperaturaZewnetrzna/>''.<br/> | ||
However, if the calculated ''<IS_TS id=strs_expidISFPrzegrodaTemperaturaPoDrugiejStronie_Uzytkownika/>'' value is higher than the actual design ''<IS_TS id=strl_expidISFPrzegrodaTemperaturaPoDrugiejStronie/>'', the program for this section assumes the actual design temperatures (for both rooms). | However, if the calculated ''<IS_TS id=strs_expidISFPrzegrodaTemperaturaPoDrugiejStronie_Uzytkownika/>'' value is higher than the actual design ''<IS_TS id=strl_expidISFPrzegrodaTemperaturaPoDrugiejStronie/>'', the program for this section assumes the actual design temperatures (for both rooms).<br/> | ||
===<IS_TS id=sNormowa/> <IS_TS id=26F6/>=== | ===<IS_TS id=sNormowa/> <IS_TS id=26F6/>=== | ||
| Line 55: | Line 55: | ||
'''<IS_TS id=strs_expidISFOZCDaneOgolneSredniaTemperaturaZewnetrzna/>''' - ''<IS_TS id=strl_expidISFOZCDaneOgolneSredniaTemperaturaZewnetrzna/>''.<br/> | '''<IS_TS id=strs_expidISFOZCDaneOgolneSredniaTemperaturaZewnetrzna/>''' - ''<IS_TS id=strl_expidISFOZCDaneOgolneSredniaTemperaturaZewnetrzna/>''.<br/> | ||
However, if the calculated value of ''<IS_TS id=strs_expidISFPrzegrodaTemperaturaPoDrugiejStronie_Uzytkownika/>'' is lower than the declared value of ''θj,u'', then the program assumes that ''θj,u'' is the temperature on the other side. | However, if the calculated value of ''<IS_TS id=strs_expidISFPrzegrodaTemperaturaPoDrugiejStronie_Uzytkownika/>'' is lower than the declared value of ''θj,u'', then the program assumes that ''θj,u'' is the temperature on the other side.<br/> | ||
===<IS_TS id=sNormowa/> <IS_TS id=26F5/> <IS_TS id=26F6/>=== | ===<IS_TS id=sNormowa/> <IS_TS id=26F5/> <IS_TS id=26F6/>=== | ||
Revision as of 07:00, 7 July 2025
| Product | InstalSystem 5 |
| Type of article | TIP&TRICK |
| Source for translation | 2025-05-23 |
Problem description
The temperature of the adjacent space should be taken into account during Thermal calculations of building.
There are several variants to Determine temperature of adjacent space in the program:
- Acc. to standard,
- Acc. to standard Observe Δθij.,
- Acc. to standard ,
- Acc. to standard Observe Δθij. ,
- Always adopt design temperature of adjacent space.
θj,u - minimum temperature of the adjacent space equals 16°C by default.
Note: Calculation variants above do not apply to rooms in a Building unit noted as Temperatures of adjacent spaces equal to design.
Solution
Acc. to standard
The Temperature on other side of the Partition located between rooms from different units is counted as follows:
θos = (θi,H + θm,e) / 2
θi,H - Design room temperature,
θm,e - Annual mean external temperature.
Acc. to standard Observe Δθij.
The Temperature on other side of the Partition located between rooms from different units is counted as follows:
θos = (θi,H + θm,e) / 2
θi,H - Design room temperature,
θm,e - Annual mean external temperature.
However, if the calculated θos value is higher than the actual design Temperature on other side, the program for this section assumes the actual design temperatures (for both rooms).
Acc. to standard
The Temperature on other side of the Partition located between rooms from different units is counted as follows:
θos = (θi,H + θm,e) / 2
θi,H - Design room temperature,
θm,e - Annual mean external temperature.
However, if the calculated value of θos is lower than the declared value of θj,u, then the program assumes that θj,u is the temperature on the other side.